You have tried turning on your Sceptre TV but despite making efforts, the result in a black screen. Well, the same issue has been faced by a lot of Sceptre TV owners and there are workarounds available to fix it. Those affected say Sceptre TV turns on but shows black screen. If you are struggling to turn on your TV, try the solutions from this article and get your Sceptre TV up and running again.
Although Sceptre TVs are well known for their build quality and performance, they are still a piece of tech at the end of the day. They also run into problems, just like TVs from other brands. However, in most cases, the black screen problem can be easily fixed.
If your Sceptre TV turns on but shows black screen, unplug the TV for 30 seconds and press and hold the power button for 20 seconds. Plug in the TV again and it should work like before.
If your Sceptre TV is turned on but shows black screen, it could be because of one of the following reasons:
- Faulty power cable or outlet
- Software glitches
- Malfunctioning power board
- Defective screen
Unless there’s a hardware defect(which is not the case with most people), you can easily troubleshoot the black screen problem on your Sceptre TV.
7 Ways to Fix Sceptre TV Turns on But Shows Black Screen Issue
Try the solutions below and get your Sceptre TV up and running again. You may have to go through every solution. Simply work your way down until you find the one that works for you.
Fix 1: Power Cycle Your Sceptre TV
Power cycling is one of the effective and quick remedy to fix the black screen issue. You should therefore do the same on your Sceptre TV to check it it can do the trick for you.
Follow these steps to power cycle your Sceptre TV:
- Turn off your TV and unplug it from the board or wall outlet.
- Press the power button to 30 seconds to remove any residual power.
- Release the power button.
- Leave the TV unplugged for another 2 minutes.
- Plug your TV back in and try switching it on.
When your power cycle your TV, it shuts down the complete by removing any residual data and clearing out temporary data.
Fix 2: Check the HDMI Connections
A loose HDMI cable can cause a black screen on your Sceptre TV. Make sure that the HDMI is firmly connected to your TV or another device.
Depending on your TV mode, the HDMI should be located either on the back or the side of the TV. Remove the HDMI cable and check if it has any signs of damage. If yes, you would want to replace it. If the cable looks fine, connect it firmly to your TV and the attached device.
If the TV screen remains black, the HDMI cable could be faulty. Replace your HDMI cable and check if the problem is fixed.
Fix 3: Inspect the Power Cord
Check if the power cable has any signs of damage or degradation. Even a slight damage can cause issues with the power supply. You should therefore examine the power cord for any damages.
Next, ensure that the power cord is firmly attached to your TV and power outlet.
If the TV shows picture, enjoy! If the problem persists, you might need to inspect the wall socket as mentioned in the next solution.
Fix 4: Try Changing the Wall Outlet
If your Sceptre TV is still showing black screen, try plugging it into a different wall outlet. The problem could be caused by a defective wall outlet which may have a proper power supply.
If the problem persists, remove the surge protector (if you using one) and plug your TV directly to the wall outlet while troubleshooting.
If your TV works afterwards, get a new surge protector. However, if you are still getting a black screen, at least you know the wall outlet and surge protector are not to be blamed.
Fix 5: Change the Input Source
An incorrect input source won’t show any content and the TV might appear completely dark.
Change the input source to the correct one and you should start seeing contents on your Sceptre TV. You can change the input source by pressing the input/source button on your remote.
Fix 6: Factory Reset Your Sceptre TV
If none of the above solutions worked, try factory resetting your TV as the last resort before reaching out to Sceptre support. It should fix all sorts of software issues on your TV.
To factory reset your TV, make sure it is plugged in and turned on. Next, locate the reset button. It’s usually present inside a small hole on the back of the TV. Use a pin to press and hold the reset button for 30 seconds.
Your Sceptre TV should automatically restart after pressing the reset button for a few seconds.
Fix 7: Contact Sceptre Support
You should contact Sceptre support to get further help with your Sceptre TV. If your product is under warranty, contact them and get a technician to visit your place to fix the black screen issue on your Sceptre TV.
Wrapping It Up
Having a Sceptre TV with no display can be frustrating. However, there are ways to fix it which we have talked about in this post. We hope this guide was useful to you.